_______________General Description
The MAX1044 and ICL7660 are monolithic, CMOS
switched-capacitor voltage converters that invert, dou-
ble, divide, or multiply a positive input voltage. They are
pin compatible with the industry-standard ICL7660 and
LTC1044. Operation is guaranteed from 1.5V to 10V with
no external diode over the full temperature range. They
deliver 10mA with a 0.5V output drop. The MAX1044
has a BOOST pin that raises the oscillator frequency
above the audio band and reduces external capacitor
size requirements.
The MAX1044/ICL7660 combine low quiescent current
and high efficiency. Oscillator control circuitry and four
power MOSFET switches are included on-chip.
Applications include generating a -5V supply from a
+5V logic supply to power analog circuitry. For applica-
tions requiring more power, the MAX660 delivers up to
100mA with a voltage drop of less than 0.65V.
________________________Applications
-5V Supply from +5V Logic Supply
Personal Communications Equipment
Portable Telephones
Op-Amp Power Supplies
EIA/TIA-232E and EIA/TIA-562 Power Supplies
Data-Acquisition Systems
Hand-Held Instruments
Panel Meters
____________________________Features
♦Miniature µMAX Package
♦1.5V to 10.0V Operating Supply Voltage Range
♦98% Typical Power-Conversion Efficiency
♦Invert, Double, Divide, or Multiply Input Voltages
♦BOOST Pin Increases Switching Frequencies
(MAX1044)
♦No-Load Supply Current: 200µA Max at 5V
♦No External Diode Required for Higher-Voltage
Operation
______________Ordering Information
Ordering Information continued at end of data sheet.
* Contact factory for dice specifications.
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
________________________________________________________________
Maxim Integrated Products
1
Call toll free 1-800-998-8800 for free samples or literature.
19-4667; Rev 1; 7/94
MAX1044
ICL7660
4
3
2
1
CAP-
GND
CAP+
(N.C.) BOOST
5
6
7
8
VOUT
LV
OSC
V+
TOP VIEW
( ) ARE FOR ICL7660
DIP/SO/µMAX
TO-99
ICL7660
N.C.
CAP+
GND
CAP-
VOUT
LV
OSC
V+ AND CASE
1
2
3
4
5
6
7
8
_________________Pin Configurations
NEGATIVE VOLTAGE CONVERTER
CAP+
CAP-
V+
VOUT
GND
INPUT
SUPPLY
VOLTAGE
NEGATIVE
OUTPUT
VOLTAGE
MAX1044
ICL7660
__________Typical Operating Circuit
Dice*
8 SO
8 Plastic DIP
PIN-PACKAGETEMP. RANGE
0°C to +70°C
0°C to +70°C
0°C to +70°CMAX1044C/D
MAX1044CSA
MAX1044CPA
PART
8 Plastic DIP-40°C to +85°CMAX1044EPA
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 1, V+ = 5.0V, LV pin = 0V, BOOST pin = open, ILOAD = 0mA, TA= TMIN to TMAX, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1: The Maxim ICL7660 and MAX1044 can operate without an external output diode over the full temperature and voltage
ranges. The Maxim ICL7660 can also be used with an external output diode in series with pin 5 (cathode at VOUT) when
replacing the Intersil ICL7660. Tests are performed without diode in circuit.
Note 2: fOSC is tested with COSC = 100pF to minimize the effects of test fixture capacitance loading. The 1pF frequency is correlat-
ed to this 100pF test point, and is intended to simulate pin 7’s capacitance when the device is plugged into a test socket
with no external capacitor. For this test, the LV pin is connected to GND for comparison to the original manufacturer’s
device, which automatically connects this pin to GND for (V+ > 3V).
Supply Voltage (V+ to GND, or GND to VOUT)....................10.5V
Input Voltage on Pins 1, 6, and 7.........-0.3V ≤VIN ≤(V+ + 0.3V)
LV Input Current ..................................................................20µA
Output Short-Circuit Duration (V+ ≤5.5V)..................Continuous
Continuous Power Dissipation (TA= +70°C)
Plastic DIP (derate 9.09mW/°C above +70°C) ............727mW
SO (derate 5.88mW/°C above +70°C).........................471mW
µMAX (derate 4.1mW/°C above +70°C) ......................330mW
CERDIP (derate 8.00mW/°C above +70°C).................640mW
TO-99 (derate 6.67mW/°C above +70°C)....................533mW
Operating Temperature Ranges
MAX1044C_ _ /ICL7660C_ _ ..............................0°C to +70°C
MAX1044E_ _ /ICL7660E_ _............................-40°C to +85°C
MAX1044M_ _ /ICL7660M_ _ ........................-55°C to +125°C
Storage Temperature Range............................-65°C to + 150°C
Lead Temperature (soldering, 10sec).............................+300°C
kHz
TA= 0°C to +70°C
TA= +25°C
TA= -55°C to +125°C
V
OSC
= 0V or V+, LV open
RL= 5kΩ, TA= +25°C, fOSC 5kHz, LV open
TA= -40°C to +85°C
RL= 10kΩ, LV open
RL= 10kΩ, LV to GND
fOSC = 2.7kHz (ICL7660) ,
fOSC = 1kHz (MAX1044),
V+ = 2V, IL= 3mA,
LV to GND
30 200
RL= ∞,
pins 1 and 7
no connection,
LV open µA
10
Supply Current
20
Pin 1 = 0V
Pin 1 = V+ 3
Oscillator Sink or
Source Current
%95 98Power Efficiency
COSC = 1pF,
LV to GND (Note 2)
400
1
Ω
325
Output Resistance
IL= 20mA,
fOSC = 5kHz,
LV open
200
TA= 0°C to +70°C
TA= -40°C to +85°C 200
UNITS
MAX1044
MIN TYP MAX
PARAMETER
325
TA= +25°C
130
325
130
150
200
V
1.5 10
Supply Voltage
Range (Note 1)
65 100
5
Oscillator Frequency
100
V+ = 2V
V+ = 5V MΩ1.0
Oscillator Impedance
80 175
95 98
400
300
250
225
ICL7660
MIN TYP MAX
300
140
250
120
150
250
3.0 10.0
1.5 3.5
55 100
10
100
1.0
TA= -55°C to +125°C
RL= ∞, pins 1 and 7 = V+ = 3V
TA= +25°C
TA= +25°C
TA= 0°C to +70°C
TA= -40°C to +85°C
TA= -55°C to +125°C
V+ = 5V
V+ = 2V
RL= ∞, TA = +25°C, LV open 99.0 99.9 %97.0 99.9Voltage Conversion Efficiency
µA
kΩ
CONDITIONS
80
90
100
30 101
EFFICIENCY
vs. OSCILLATOR FREQUENCY
70
MAX1044-Fig 7
OSCILLATOR FREQUENCY (Hz)
EFFICIENCY (%)
104
50
40
1021036x105
60
105
C1, C2 = 100µF
C1, C2 = 10µF
C1, C2 = 1µF
EXTERNAL
HCMOS
OSCILLATOR
10,000
100,000
0.11
OSCILLATOR FREQUENCY
vs. EXTERNAL CAPACITANCE
1000
MAX1044-Fig 8
COSC (pF)
OSCILLATOR FREQUENCY (Hz)
1000
10
1
10 100 100,000
100
10,000
ICL7660 and
MAX1044 with
BOOST = OPEN
MAX1044 with
BOOST -V+
1001
OSCILLATOR FREQUENCY
vs. SUPPLY VOLTAGE
MAX1044-Fig 9
SUPPLY VOLTAGE (V)
OSCILLATOR FREQUENCY (Hz)
4
10,000
1000
23 678910
100,000
5
FROM TOP TO BOTTOM AT 5V
MAX1044, BOOST = V+, LV = GND
MAX1044, BOOST = V+, LV = OPEN
ICL7660, LV = GND
ICL7660, LV = OPEN
MAX1044, BOOST = OPEN, LV = GND
MAX1044, BOOST = OPEN, LV = OPEN
0012345678910
OUTPUT VOLTAGE and OUTPUT RIPPLE
vs. LOAD CURRENT
-0.5
-2.0
MAX1044-Fig 1
LOAD CURRENT (mA)
OUTPUT VOLTAGE (V)
OUTPUT RIPPLE (mVp-p)
-1.5
-1.0
0
250
200
150
100
50
400
350
300
OUTPUT
VOLTAGE
V+ = 2V
LV = GND
OUTPUT RIPPLE
A: MAX1044 with
BOOST = V+
B: ICL7660
C: MAX1044 with
BOOST = OPEN
A
B
C
00 5 10 15 20 25 30 35 40
OUTPUT VOLTAGE and OUTPUT RIPPLE
vs. LOAD CURRENT
-0.5
-2.0
-2.5
-3.0
-3.5
-4.0
-4.5
-5.0
MAX1044-Fig 2
LOAD CURRENT (mA)
OUTPUT VOLTAGE (V)
OUTPUT RIPPLE (mVp-p)
-1.5
-1.0
0
720
640
560
480
400
320
240
160
80
800
OUTPUT VOLTAGE
OUTPUT RIPPLE
V+ = 5V
LV = OPEN
A
A
B
C
B
C
A: MAX1044 with
BOOST = V+
B: ICL7660
C: MAX1044 with
BOOST = OPEN
00 5 10 15 20 25 30 35 40
OUTPUT VOLTAGE and OUTPUT RIPPLE
vs. LOAD CURRENT
-1
-4
-5
-6
-7
-8
-9
-10
MAX1044-Fig 3
LOAD CURRENT (mA)
OUTPUT VOLTAGE (V)
OUTPUT RIPPLE (mVp-p)
-3
-2
0
700
630
560
490
420
350
280
210
140
70
V+ = 10V
LV = OPEN
OUTPUT
RIPPLE
A
B
A: MAX1044 with
BOOST = V+
B: ICL7660
C: MAX1044 with
BOOST = OPEN
C
BC
A
OUTPUT
VOLTAGE
0012345678910
EFFICIENCY and SUPPLY CURRENT
vs. LOAD CURRENT
10
40
50
60
70
80
90
100
MAX1044-Fig 4
LOAD CURRENT (mA)
EFFICIENCY (%)
SUPPLY CURRENT (mA)
30
20
0
7
8
9
10
6
5
4
3
2
1
SUPPLY CURRENT
EFFICIENCY
V+ = 2V
LV = GND 00 5 10 15 20 25 30 35 40
EFFICIENCY and SUPPLY CURRENT
vs. LOAD CURRENT
10
40
50
60
70
80
90
100
MAX1044-Fig 5
LOAD CURRENT (mA)
EFFICIENCY (%)
SUPPLY CURRENT (mA)
30
20
0
35
40
45
50
30
25
20
15
10
5
V+ = 5V
LV = OPEN
EFFICIENCY
A: MAX1044 with
BOOST = V+
B: ICL7660
C: MAX1044 with
BOOST = OPEN
SUPPLY CURRENT
B
C
A
00 5 10 15 20 25 30 35 40
EFFICIENCY and SUPPLY CURRENT
vs. LOAD CURRENT
10
40
50
60
70
80
90
100
MAX1044-Fig 6
LOAD CURRENT (mA)
EFFICIENCY (%)
SUPPLY CURRENT (mA)
30
20
0
35
40
45
50
30
25
20
15
10
5
V+ = 10V
LV = OPEN
A: MAX1044 with
BOOST = V+
B: ICL7660
C: MAX1044 with
BOOST = OPEN
SUPPLY CURRENT
B, C
EFFICIENCY
A
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
_______________________________________________________________________________________
3
__________________________________________Typical Operating Characteristics
(V+ = 5V; CBYPASS = 0.1µF; C1 = C2 = 10µF; LV = open; OSC = open; TA= +25°C; unless otherwise noted.)
0.112345678910
QUIESCENT CURRENT
vs. SUPPLY VOLTAGE
MAX1044-Fig 12
SUPPLY VOLTAGE (V)
QUIESCENT CURRENT (µA)
10
1
100
1000
2000
A
B
DC
A: MAX1044, BOOST = V+, LV = GND
B: MAX1044, BOOST = V+, LV = OPEN
C: ICL7660 and MAX1044 with
BOOST = OPEN, LV = GND;
ABOVE 5V, MAX1044 ONLY
D: ICL7660 and MAX1044 with
BOOST = OPEN, LV = OPEN
0
101102103104105
OUTPUT RESISTANCE
vs. OSCILLATOR FREQUENCY
MAX1044-Fig 14
FREQUENCY (Hz)
RESISTANCE (Ω)
200
100
300
400
500
600
700
800
900
1000
C1, C2 = 100µF
C1, C2 = 1µF
C1, C2 = 10µF
EXTERNAL
HCMOS
OSCILLATOR
0-50 -25 0 25 50 75 100 125
QUIESCENT CURRENT
vs. TEMPERATURE
MAX1044-Fig 13
TEMPERATURE (°C)
QUIESCENT CURRENT (µA)
200
100
300
400
500
ICL7660, MAX1044 with BOOST = OPEN
MAX1044 with
BOOST = V+
012345678910
OUTPUT RESISTANCE
vs. SUPPLY VOLTAGE
MAX1044-Fig 15
SUPPLY VOLTAGE (V)
OUTPUT RESISTANCE (Ω)
40
20
60
80
100
120
140
160
180
200
20-60 -40 -20 0 20 40 60 80 100 120 140
OUTPUT RESISTANCE
vs. TEMPERATURE
MAX1044-Fig 16
TEMPERATURE (°C)
OUTPUT RESISTANCE (Ω)
40
30
50
60
70
80
ICL7660,
MAX1044 with
BOOST = OPEN
MAX1044 with
BOOST = V+
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
4 _______________________________________________________________________________________
____________________________Typical Operating Characteristics (continued)
(V+ = 5V; CBYPASS = 0.1µF; C1 = C2 = 10µF; LV = open; OSC = open; TA= +25°C; unless otherwise noted.)
0-50
OSCILLATOR FREQUENCY
vs. TEMPERATURE
MAX1044-Fig 10
TEMPERATURE (°C)
OSCILLATOR FREQUENCY (kHz)
25
40
20
-25 0 75 100 125
60
80
100
50
A: MAX1044 with
BOOST = V+
B: ICL7600
C: MAX1044 with
BOOST = OPEN
B
A
C1
1001011021031041055x105
QUIESCENT CURRENT
vs. OSCILLATOR FREQUENCY
MAX1044-Fig 11
OSCILLATOR FREQUENCY (Hz)
QUIESCENT CURRENT (µA)
100
10
1000
10,000
USING
EXTERNAL
HCMOS
OSCILLATOR
USING
EXTERNAL
CAPACITOR
_______________Detailed Description
The MAX1044/ICL7660 are charge-pump voltage con-
verters. They work by first accumulating charge in a
bucket capacitor and then transfer it into a reservoir
capacitor. The ideal voltage inverter circuit in Figure 2
illustrates this operation.
During the first half of each cycle, switches S1 & S3
close and switches S2 & S4 open, which connects the
bucket capacitor C1 across V+ and charges C1.
During the second half of each cycle, switches S2 & S4
close and switches S1 & S3 open, which connects the
positive terminal of C1 to ground and shifts the nega-
tive terminal to VOUT. This connects C1 in parallel with
the reservoir capacitor C2. If the voltage across C2 is
smaller than the voltage across C1, then charge flows
from C1 to C2 until the voltages across them are equal.
During successive cycles, C1 will continue pouring
charge into C2 until the voltage across C2 reaches
- (V+). In an actual voltage inverter, the output is less
than - (V+) since the switches S1–S4 have resistance
and the load drains charge from C2.
Additional qualities of the MAX1044/ICL7660 can be
understood by using a switched-capacitor circuit
model. Switching the bucket capacitor, C1, between
the input and output of the circuit synthesizes a resis-
tance (Figures 3a and 3b.)
When the switch in Figure 3a is in the left position,
capacitor C1 charges to V+. When the switch moves to
the right position, C1 is discharged to VOUT. The
charge transferred per cycle is: ∆Q = C1(V+ - VOUT). If
the switch is cycled at frequency f, then the resulting
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
_______________________________________________________________________________________ 5
MAX1044
ICL7660
BOOST
CAP+
GND
CBYPASS
= 0.1µF
V+
RL
CAP-
V+
OSC
C1
10µFLV
VOUT C2
10µF
COSC
EXTERNAL
OSCILLATOR
VOUT
_____________________________________________________________ Pin Description
NAME FUNCTION
BOOST
(MAX1044) Frequency Boost. Connecting BOOST to V+ increases the oscillator frequency by a factor of six. When the
oscillator is driven externally, BOOST has no effect and should be left open.
PIN
1N.C.
(ICL7660) No Connection
3 GND Ground. For most applications, the positive terminal of the reservoir capacitor is connected to this pin.
2 CAP+ Connection to positive terminal of Charge-Pump Capacitor
6 LV Low-Voltage Operation. Connect to ground for supply voltages below 3.5V.
ICL7660: Leave open for supply voltages above 5V.
5 VOUT Negative Voltage Output. For most applications, the negative terminal of the reservoir capacitor is
connected to this pin.
4 CAP- Connection to negative terminal of Charge-Pump Capacitor
7 OSC Oscillator Control Input. Connecting an external capacitor reduces the oscillator frequency. Minimize stray
capacitance at this pin.
8 V+ Power-Supply Positive Voltage Input. (1.5V to 10V). V+ is also the substrate connection.
Figure 1. Maxim MAX1044/ICL7660 Test Circuit
MAX1044/ICL7660
current is: I = f x ∆Q = f x C1(V+ - VOUT). Rewriting this
equation in Ohm’s law form defines an equivalent resis-
tance synthesized by the switched-capacitor circuit
where:
where f is one-half the oscillator frequency. This resis-
tance is a major component of the output impedance of
switched-capacitor circuits like the MAX1044/ICL7660.
As shown in Figure 4, the MAX1044/ICL7660 contain
MOSFET switches, the necessary transistor drive cir-
cuitry, and a timing oscillator.
________________Design Information
The MAX1044/ICL7660 are designed to provide a
simple, compact, low-cost solution where negative or
doubled supply voltages are needed for a few low-
power components. Figure 5 shows the basic negative
voltage converter circuit. For many applications, only
two external capacitors are needed. The type of
capacitor used is not critical.
Proper Use of the Low-Voltage (LV) Pin
Figure 4 shows an internal voltage regulator inside the
MAX1044/ICL7660. Use the LV pin to bypass this
regulator, in order to improve low-voltage performance
I(V+ - V )
1 / (f x C1)
R1
f x C1
OUT
EQUIV
=
=
and
Switched-Capacitor Voltage Converters
6 _______________________________________________________________________________________
S1
V+ S2
S3 S4
C1
C2
VOUT = -(V+)
Figure 2. Ideal Voltage Inverter
V+
C1
f
C2 RLOAD
VOUT
Figure 3a. Switched Capacitor Model
REQUIV =
REQUIV
VOUT
RLOAD
1
V+
f × C1
C2
Figure 3b. Equivalent Circuit
1M
BOOST
pin 1
OSC
pin 7
LV
pin 6 GND
pin 3 CAP-
pin 4
S2
S1
S4S3
CAP+
pin 2
V+
pin 8
VOUT
pin 5
÷ 2
Q
OSCILLATOR
INTERNAL 
REGULATOR
Q
Figure 4. MAX1044 and ICL7660 Functional Diagram
and allow operation down to 1.5V. For low-voltage
operation and compatibility with the industry-standard
LTC1044 and ICL7660, the LV pin should be connect-
ed to ground for supply voltages below 3.5V and left
open for supply voltages above 3.5V.
The MAX1044’s LV pin can be grounded for all operat-
ing conditions. The advantage is improved low-voltage
performance and increased oscillator frequency. The
disadvantage is increased quiescent current and
reduced efficiency at higher supply voltages. For
Maxim’s ICL7660, the LV pin must be left open for
supply voltages above 5V.
When operating at low supply voltages with LV open,
connections to the LV, BOOST, and OSC pins should
be short or shielded to prevent EMI from causing
oscillator jitter.
Oscillator Frequency Considerations
For normal operation, leave the BOOST and OSC pins
of the MAX1044/ICL7660 open and use the nominal
oscillator frequency. Increasing the frequency reduces
audio interference, output resistance, voltage ripple,
and required capacitor sizes. Decreasing frequency
reduces quiescent current and improves efficiency.
Oscillator Frequency Specifications
The MAX1044/ICL7660 do not have a precise oscillator
frequency. Only minimum values of 1kHz and 5kHz for
the MAX1044 and a typical value of 10kHz for the
ICL7660 are specified. If a specific oscillator frequency
is required, use an external oscillator to drive the OSC
pin.
Increasing Oscillator Frequency
Using the BOOST Pin
For the MAX1044, connecting the BOOST pin to the V+
pin raises the oscillator frequency by a factor of about 6.
Figure 6 shows this connection. Higher frequency oper-
ation lowers output impedance, reduces output ripple,
allows the use of smaller capacitors, and shifts switch-
ing noise out of the audio band. When the oscillator is
driven externally, BOOST has no effect and should be
left open. The BOOST pin should also be left open for
normal operation.
Reducing the Oscillator Frequency Using COSC
An external capacitor can be connected to the OSC pin
to lower the oscillator frequency (Figure 6). Lower
frequency operation improves efficiency at low load
currents by reducing the IC’s quiescent supply current.
It also increases output ripple and output impedance.
This can be offset by using larger values for C1 and C2.
Connections to the OSC pin should be short to prevent
stray capacitance from reducing the oscillator frequency.
Overdriving the OSC Pin with an External Oscillator
Driving OSC with an external oscillator is useful when
the frequency must be synchronized, or when higher
frequencies are required to reduce audio interference.
The MAX1044/ICL7660 can be driven up to 400kHz.
The pump and output ripple frequencies are one-half
the external clock frequency. Driving the
MAX1044/ICL7660 at a higher frequency increases the
ripple frequency and allows the use of smaller
capacitors. It also increases the quiescent current.
The OSC input threshold is V+ - 2.5V when V+ ≥5V,
and is V+ / 2 for V+ < 5V. If the external clock does not
swing all the way to V+, use a 10kΩpull-up resistor
(Figure 7).
Output Voltage Considerations
The MAX1044/ICL7660 output voltage is not regulated.
The output voltages will vary under load according to
the output resistance. The output resistance is primarily
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
_______________________________________________________________________________________ 7
MAX1044
ICL7660
4
3
C1
10µF
*REQUIRED FOR V+ < 3.5V
VOUT = -(V+)
C2
10µF
V+
2
1
5
6
7
8
*
CBYPASS
Figure 5. Basic Negative Voltage Converter
MAX1044
4
3
10µF COSC
VOUT = -(V+)
10µF
V+
2
1
5
6
7
8
CONNECTION 
FROM V+ 
TO BOOST
Figure 6. Negative Voltage Converter with C
OSC
and BOOST
MAX1044/ICL7660
a function of oscillator frequency and the capacitor
value. Oscillator frequency, in turn, is influenced by
temperature and supply voltage. For example, with a
5V input voltage and 10µF charge-pump capacitors,
the output resistance is typically 50Ω. Thus, the output
voltage is about -5V under light loads, and decreases
to about -4.5V with a 10mA load current.
Minor supply voltage variations that are inconsequential
to digital circuits can affect some analog circuits.
Therefore, when using the MAX1044/ICL7660 for
powering sensitive analog circuits, the power-supply
rejection ratio of those circuits must be considered.
The output ripple and output drop increase under
heavy loads. If necessary, the MAX1044/ICL7660 out-
put impedance can be reduced by paralleling devices,
increasing the capacitance of C1 and C2, or connect-
ing the MAX1044’s BOOST pin to V+ to increase the
oscillator frequency.
Inrush Current and EMI Considerations
During start-up, pump capacitors C1 and C2 must be
charged. Consequently, the MAX1044/ICL7660 devel-
op inrush currents during start-up. While operating,
short bursts of current are drawn from the supply to C1,
and then from C1 to C2 to replenish the charge drawn
by the load during each charge-pump cycle. If the
voltage converters are being powered by a high-
impedance source, the supply voltage may drop too
low during the current bursts for them to function prop-
erly. Furthermore, if the supply or ground impedance is
too high, or if the traces between the converter IC and
charge-pump capacitors are long or have large loops,
switching noise and EMI may be generated. To reduce
these effects:
1) Power the MAX1044/ICL7600 from a low-impedance
source.
2) Add a power-supply bypass capacitor with low
effective series resistance (ESR) close to the IC
between the V+ and ground pins.
3) Shorten traces between the IC and the charge-pump
capacitors.
4) Arrange the components to keep the ground pins of
the capacitors and the IC as close as possible.
5) Leave extra copper on the board around the voltage
converter as power and ground planes. This is
easily done on a double-sided PC board.
Efficiency, Output Ripple,
and Output Impedance
The power efficiency of a switched-capacitor voltage
converter is affected by the internal losses in the con-
verter IC, resistive losses of the pump capacitors, and
conversion losses during charge transfer between the
capacitors. The total power loss is:
The internal losses are associated with the IC’s internal
functions such as driving the switches, oscillator, etc.
These losses are affected by operating conditions such
as input voltage, temperature, frequency, and connec-
tions to the LV, BOOST, and OSC pins.
The next two losses are associated with the output
resistance of the voltage converter circuit. Switch losses
occur because of the on-resistances of the MOSFET
switches in the IC. Charge-pump capacitor losses
occur because of their ESR. The relationship between
these losses and the output resistance is as follows:
where:
and fOSC is the oscillator frequency.
R1
(f / 2) x C1
4 2R ESR ESR
OUT OSC
SWITCHES C1 C2
≅+
+
()
+
P P I x R
OUT2OUT
+=
∑ P = P +P +P +P
Switched-Capacitor Voltage Converters
8 _______________________________________________________________________________________
MAX1044
ICL7660
4
3
10µF
VOUT = -(V+)
10µF
V+
V+
CMOS or
TTL GATE
10kΩ
REQUIRED
FOR TTL
2
1
5
6
7
8
Figure 7. External Clocking
LOSS INTERNAL
LOSSES SWITCH
LOSSES PUMP
CAPACITOR
LOSSES
CONVERSION
LOSSES
PUMP
CAPACITOR
LOSSES
SWITCH
LOSSES
The first term is the effective resistance from the
switched-capacitor circuit.
Conversion losses occur during the transfer of charge
between capacitors C1 and C2 when there is a voltage
difference between them. The power loss is:
Increasing Efficiency
Efficiency can be improved by lowering output voltage
ripple and output impedance. Both output voltage rip-
ple and output impedance can be reduced by using
large capacitors with low ESR.
The output voltage ripple can be calculated by noting
that the output current is supplied solely from capacitor
C2 during one-half of the charge-pump cycle.
Slowing the oscillator frequency reduces quiescent cur-
rent. The oscillator frequency can be reduced by con-
necting a capacitor to the OSC pin.
Reducing the oscillator frequency increases the ripple
voltage in the MAX1044/ICL7660. Compensate by
increasing the values of the bucket and reservoir
capacitors. For example, in a negative voltage converter,
the pump frequency is around 4kHz or 5kHz. With the
recommended 10µF bucket and reservoir capacitors,
the circuit consumes about 70µA of quiescent current
while providing 20mA of output current. Setting the
oscillator to 400Hz by connecting a 100pF capacitor to
OSC reduces the quiescent current to about 15µA.
Maintaining 20mA output current capability requires
increasing the bucket and reservoir capacitors to
100µF.
Note that lower capacitor values can be used for lower
output currents. For example, setting the oscillator to
40Hz by connecting a 1000pF capacitor to OSC pro-
vides the highest efficiency possible. Leaving the bucket
and reservoir capacitors at 100µF gives a maximum
IOUT of 2mA, a no-load quiescent current of 10µA, and
a power conversion efficiency of 98%.
General Precautions
1) Connecting any input terminal to voltages greater
than V+ or less than ground may cause latchup. Do
not apply any input sources operating from external
supplies before device power-up.
2) Never exceed maximum supply voltage ratings.
3) Do not connect C1 and C2 with the wrong polarity.
4) Do not short V+ to ground for extended periods with
supply voltages above 5.5V present on other pins.
5) Ensure that VOUT (pin 5) does not go more positive
than GND (pin 3). Adding a diode in parallel with
C2, with the anode connected to VOUT and cathode
to LV, will prevent this condition.
________________Application Circuits
Negative Voltage Converter
Figure 8 shows a negative voltage converter, the most
popular application of the MAX1044/ICL7660. Only two
external capacitors are needed. A third power-supply
bypass capacitor is recommended (0.1µF to 10µF)
V1
2 x f x C2 2 x ESR I
RIPPLE OSC C2 OUT
≅+
P
1
2
C1 (V V
1
2C2 V 2V V x f / 2
CONV.LOSS OUT2
RIPPLE2OUT RIPPLE OSC
)
=+−
+
−
2
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
_______________________________________________________________________________________ 9
MAX1044
ICL7660
4
3
C1
10µF
VOUT = -(V+)
CBYPASS
0.1µF
2
1
5
6
7
8
C2
10µF
V+
BOOST
LV
Figure 8. Negative Voltage Converter with BOOST and LV
Connections
MAX1044
ICL7660
4
3
VOUT = 2(V+) - 2VD
2
1
5
6
7
8
C1 C2
V+
Figure 9. Voltage Doubler
MAX1044/ICL7660
Positive Voltage Doubler
Figure 9 illustrates the recommended voltage doubler
circuit for the MAX1044/ICL7660. To reduce the voltage
drops contributed by the diodes (VD), use Schottky
diodes. For true voltage doubling or higher output cur-
rents, use the MAX660.
Voltage Divider
The voltage divider shown in Figure 10 splits the power
supply in half. A third capacitor can be added between
V+ and VOUT.
Combined Positive Multiplication and
Negative Voltage Conversion
Figure 11 illustrates this dual-function circuit.
Capacitors C1 and C3 perform the bucket and reser-
voir functions for generating the negative voltage.
Capacitors C2 and C4 are the bucket and reservoir
capacitors for the doubled positive voltage. This circuit
has higher output impedances resulting from the use of
a common charge-pump driver.
Cascading Devices
Larger negative multiples of the supply voltage can be
obtained by cascading MAX1044/ICL7660 devices
(Figure 12). The output voltage is nominally VOUT = -n(V+)
where n is the number of devices cascaded. The out-
put voltage is reduced slightly by the output resistance
of the first device, multiplied by the quiescent current of
the second, etc. Three or more devices can be cascaded
in this way, but output impedance rises dramatically.
For example, the output resistance of two cascaded
MAX1044s is approximately five times the output resis-
tance of a single voltage converter. A better solution
may be an inductive switching regulator, such as the
MAX755, MAX759, MAX764, or MAX774.
Switched-Capacitor Voltage Converters
10 ______________________________________________________________________________________
MAX1044
ICL7660
4
3
2
1
5
6
7
8
C2
10µF
C1
10µF
V+
VOUT = V+
1
2
LV
Figure 10. Voltage Divider
MAX1044
ICL7660
4
3
VOUT = 2(V+) - 2VD
2
1
5
6
7
8
C4
C1
C2
V+
VOUT = -(V+)
C3
LV
Figure 11. Combined Positive and Negative Converter
MAX1044
ICL7660
4
3
2
1
5
6
7
8
MAX1044
ICL7660
4
3
2
1
5
6
7
8
10µF
10µF
V+
10µF
10µF
10µF
VOUT = -n(V+)
10µF
MAX1044
ICL7660
4
3
2
1
5
6
7
8
123
Figure 12. Cascading MAX1044/ICL7660 for Increased Output Voltage
Paralleling Devices
Paralleling multiple MAX1044/ICL7660s reduces output
resistance and increases current capability. As illus-
trated in Figure 13, each device requires its own pump
capacitor C1, but the reservoir capacitor C2 serves all
devices. The equation for calculating output resistance is:
Shutdown Schemes
Figures 14a–14c illustrate three ways of adding shut-
down capability to the MAX1044/ICL7660. When using
these circuits, be aware that the additional capacitive
loading on the OSC pin will reduce the oscillator fre-
quency. The first circuit has the least loading on the
OSC pin and has the added advantage of controlling
shutdown with a high or low logic level, depending on
the orientation of the switching diode.
R
R (of MAX1044 or ICL7660)
n (number of devices)
OUT OUT
=
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
______________________________________________________________________________________ 11
MAX1044
ICL7660
4
3
VOUT = -(V+)
2
1
5
6
7
8
C2
C1
V+
MAX1044
ICL7660
4
3
2
1
5
6
7
8
C1
1
n
Figure 13. Paralleling MAX1044/ICL7660 to Reduce Output
Resistance
MAX1044
ICL7660
4
3
10µF
VOUT = -(V+)
10µF
CMOS or
TTL GATE
1N4148
V+
2
1
5
6
7
8V+
10kΩ REQUIRED FOR TTL
Figure 14a-14c. Shutdown Schemes for MAX1044/ICL7660
OUTPUT
ENABLE
74HC126 OR
74LS126
TRI-STATE BUFFER
V+
7
MAX1044
ICL7660
74HC03
OPEN-DRAIN OR
74LS03
OPEN-COLLECTOR
NAND GATES
V+
MAX1044
ICL7660
7
a)
b)
c)
8 CERDIP**
8 SO
PIN-PACKAGETEMP. RANGE
-40°C to +85°C
-55°C to +125°CMAX1044MJA
MAX1044ESA
PART
8 Plastic DIP0°C to +70°C
ICL7660CPA 8 SO0°C to +70°CICL7660CSA 8 µMAX0°C to +70°CICL7660CUA Dice*0°C to +70°CICL7660C/D 8 Plastic DIP-40°C to +85°CICL7660EPA 8 SO-40°C to +85°CICL7660ESA 8 CERDIP**-55°C to +125°CICL7660AMJA†
8 TO-99**-55°C to +125°CICL7660AMTV†
_Ordering Information (continued)
* Contact factory for dice specifications.
** Contact factory for availability.
†
The Maxim ICL7660 meets or exceeds all “A” and “S”
specifications.
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12
__________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1994 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
MAX1044/ICL7660
Switched-Capacitor Voltage Converters
__________________________________________________________Chip Topographies
GND
CAP-
LV
VOUT
TRANSISTOR COUNT: 71
SUBSTRATE CONNECTED TO V+
CAP+ 0.084"
(2.1mm)
0.060"
(1.5mm)
V+
OSC
ICL7660
GND CAP+ BOOST
0.076"
(1.930mm)
0.076"
(1.930mm)
CAP-
VOUT
V+
OSCLV
TRANSISTOR COUNT: 72
SUBSTRATE CONNECTED TO V+
MAX1044
L
α
C
A1B
DIM
A
A1
B
C
D
E
e
H
L
α
MIN
0.036
0.004
0.010
0.005
0.116
0.116
0.188
0.016
0°
MAX
0.044
0.008
0.014
0.007
0.120
0.120
0.198
0.026
6°
MIN
0.91
0.10
0.25
0.13
2.95
2.95
4.78
0.41
0°
MAX
1.11
0.20
0.36
0.18
3.05
3.05
5.03
0.66
6°
INCHES MILLIMETERS
8-PIN µMAX
PACKAGE
0.650.0256
21-0036
A
e
E H
D
0.127mm
0.004 in
________________________________________________________Package Information
ENGLISH • ???? • ??? • ???
WHAT'S NEW
PRODUCTS
SOLUTIONS
DESIGN
APPNOTES
SUPPORT
BUY
COMPANY
MEMBERS
Maxim > Products > Power and Battery Management Protection and I solation
ICL7660, MAX1044
Switched-Capacitor Voltage C onverters
20mA Charge Pump with Industry Standard Pinout
QuickView
Technical Documents
Ordering Info
More Information
All
Ordering Information
Notes:
Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales.1.
Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one
business day.
2.
Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: SeeFull Data
Sheet or Part Naming Conventions.
3.
* Some packages have variations, listed on the drawing. "PkgCode/Variation" tells which variation the product uses.4.
Devices: 1-44 of 44
ICL7660
Free
Sam ple
Buy
Package:
TYPE PINS FOOTPRINT
DRAWING CODE/VAR *
Temp
RoHS/Lead-Free?
Materials Analysis
ICL7660EJA
Ceramic DIP;8 pin;81 mm
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J8-2*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660IJA
Ceramic DIP;8 pin;81 mm
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J8-2*
-20C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660AMJA
Ceramic DIP;8 pin;81 mm
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J8-2*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
ICL7660AMJA/883B
Ceramic DIP;8 pin;81 mm
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J8-2*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
ICL7660C TV
Gold Can -TO;8 pin;88 mm
Dwg: 21-0022A (PDF)
Use pkgcode/variation: G99-8*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
ICL7660AMTV
Gold Can -TO;8 pin;88 mm
Dwg: 21-0022A (PDF)
Use pkgcode/variation: G99-8*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
ICL7660AMTV/883B
Gold Can -TO;8 pin;88 mm
Dwg: 21-0022A (PDF)
Use pkgcode/variation: G99-8*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
ICL7660AMTV/HR
Metal C an-TO;8 pin;88 mm
Dwg: 21-0022A (PDF)
Use pkgcode/variation: T99-8*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
ICL7660EPA+
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8+1*
-40C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660IPA+
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8+1*
-20C to +85C
RoHS/Lead-Free: See data sheet
Materials Analysis
ICL7660C PA+
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8+1*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660C PA
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
ICL7660EPA
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8-1*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660IPA
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8-1*
-20C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660C SA
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-4*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
ICL7660C SA+T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+4*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660C SA-T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-4*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
ICL7660C SA+
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+4*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660ESA+T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+4*
-40C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660ESA+
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+4*
-40C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660ESA-T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-4*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660ESA
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-4*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660ISA-T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-4*
-20C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660ISA+T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+4*
-20C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660ISA+
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+4*
-20C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660ISA
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-4*
-20C to +85C
RoHS/Lead-Free: No
Materials Analysis
ICL7660C UA+T
uMAX;8 pin;16 mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660C UA+
uMAX;8 pin;16 mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8+1*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
ICL7660C UA
uMAX;8 pin;16 mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
ICL7660C UA-T
uMAX;8 pin;16 mm
Dwg: 21-0036J (PDF)
Use pkgcode/variation: U8-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX1044
Free
Sam ple
Buy
Package:
TYPE PINS FOOTPRINT
DRAWING CODE/VAR *
Temp
RoHS/Lead-Free?
Materials Analysis
MAX1044MJA
Ceramic DIP;8 pin;81 mm
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J8-2*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX1044MJA/883B
Ceramic DIP;8 pin;81 mm
Dwg: 21-0045A (PDF)
Use pkgcode/variation: J8-2*
-55C to +125C
RoHS/Lead-Free: No
Materials Analysis
MAX1044EPA+
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8+1*
-40C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
MAX1044CPA+
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8+1*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
MAX1044CPA
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8-1*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX1044EPA
PDIP;8 pin;82 mm
Dwg: 21-0043D (PDF)
Use pkgcode/variation: P8-1*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX1044CSA
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX1044CSA-T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
0C to +70C
RoHS/Lead-Free: No
Materials Analysis
MAX1044CSA+T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
MAX1044CSA+
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
0C to +70C
RoHS/Lead-Free: Lead Free
Materials Analysis
MAX1044ESA+T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-40C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
MAX1044ESA
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX1044ESA-T
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8-2*
-40C to +85C
RoHS/Lead-Free: No
Materials Analysis
MAX1044ESA+
SOIC;8 pin;31 mm
Dwg: 21-0041B (PDF)
Use pkgcode/variation: S8+2*
-40C to +85C
RoHS/Lead-Free: Lead Free
Materials Analysis
Didn't Find What You Need?
Next Day Product Selection Assistance from Applications Engineers
Parametric Search
Applications Help
QuickView
Technical Documents
Ordering Info
More Information
Description
Key Features
Applications/U s es
Key Specifications
Diagram
Data Sheet
Application Notes
Design Guides
Engineering Journals
Reliability Reports
Software/Models
Evaluation Kits
P rice and A vailability
Samples
Buy O nline
P ackage I nformation
Lead-Free Information
Related Products
Notes and C omments
Evaluation Kits
Document Ref.: 1 9 -4667; Rev 1; 1994-07-28
This page last modified: 200 7 -05-29
CONTACT US: SEND US AN EMAIL
C opyright 200 7 by Maxim Integrated Products, Dallas Semic onductor • Legal Notices • Privacy Policy