Curtis Industries
A Division of Powers Holdings, Inc.
www.curtisind.com Specifications subject to change.
Dimensions are shown for
reference purposes only.
POWER ENTRY MODULES
56
Combination
NOTE: Other combinations of terminals may be specified on special order.
Features:
• RFI Filter Module Combines IEC Connector, Fusing,
Optional Voltage Select and On/Off Switch into a
Single, Space-Efficient Assembly
• Enhanced Low Frequency Response with No
Resonant Peaks
• Fully Shielded for Radiative Noise Control
• Accepts Either U.S. or European Standard Fuse
Sizes. Dual or Single Power Line Fusing
Specifications:
Rated Voltage: 250VAC Maximum - 50/60 Hz
Rated Current: 115VAC 250VAC
10A 10A
Current Overload: 6X for 8 seconds
Hi-Pot Test (1 min):
Line to Ground 1500VAC
Line to Line 2250VDC
Insulation Resistance: 9 x 109 Ω at 100VDC
Ambient Temperature: 40°C Max at rated current
Humidity Range: 0% to 95% R.H.
Termination:
• QC – Quick Connect
• IEC Receptacle
Maximum Leakage Current:
Each Line to Ground PE1 PE1-PO
115VAC, 60Hz: 0.25mA 0.4mA
250VAC, 50Hz: 0.40mA .75mA
Voltage Select Card: Installed in 120VAC position
unless otherwise specified
Agency Approvals:
Nominal
Current
Rating
Part
Number Termination
Line/Load
MINIMUM INSERTION LOSS - dB (50 ohm Circuit)
MODE Frequency - MHz
.05 .15 .50 .10 5.0 10 30
10A
PE1XXX10 IEC/QC Common
Differential 10
10 20
20 30
30 38
35 45
55 50
60 50
55
PE1XXXP0 IEC/QC Common
Differential 13
10 24
20 33
30 38
35 48
65 54
65 54
55
PE1 Series
PE1 Series Simplified
Schematic without Voltage Selector
PE1 Series Simplified Schematic with Voltage Selector
LOAD
1
2
3
4
110V
110V
LINE
L
N
G
FUSING
1 POLE
2 POLE
L
N
G
LOAD
L
N
G
1
2
3
4
LINE
L
N
G
2 POLE
FUSING
1 POLE
Curtis Industries
A Division of Powers Holdings, Inc. 1-800-657-0853
Dimensions are in inches and millimeters
unless otherwise specified.
Values in parentheses are metric equivalents.
POWER ENTRY MODULES
57
Combination
PE1
(10Amp)
Dimensions
Refer to Standard
Mounting Cutouts on
Page 58
2.58
(65,5)
Max.
1.99
(50,5)
H
1.575
(40,01)
1.15
(29,2)
Max.
3.20
(81,3)
3.00
(76,2)
2.41
(61,2)
Max.
1.12
(28,4)
13
24
INST ALLA TION INSTRUCTION
IMPORTANT – CHANGING
FUSE/VOLTAGE
PE1
To change fuse, remove power cord.
Remove voltage selector and replace
fuse. Reinsert fuse holder. To change
the operating voltage on the PE1
Series, remove the power cord and
rotate fuse holder block until desired
voltage aligns with the mark on the
module housing.
• Filter shipped without fuse.
Always use caution when selecting
and changing fuses and voltage
requirements. Curtis Industries is
not responsible for malfunction due
to improper installation/selection of
fuse and/or voltage select.
SERIES
PE = Power Entry
PM = Medical
Power Entry
VOLTAGE SELECTOR
0 = No Selector
3 = 115-230 V AC
OPTIONS
(Consult Factory)
1 = Standard Units
P = High Performance
Insertion Loss
SWITCH
0 = No Switch
1 = SPST Rocker Switch
2 = DPST Rocker Switch
CURRENT RATING
0 = 10 AMP
MOUNTING
METHOD & FUSING
6 = Screw Mount Metric or U.S. Fuse*
8 = Screw Mount 2 Metric or U.S. Fuses
* U.S. Fuse not available without
voltage selector
How to Order
WITH
VOLTAGE
SELECTOR
PE1 X X X X 0
L
I
N
E
L
O
A
D
