LP38851 LP38851 800 mA Fast-Response High-Accuracy Adjustable LDO Linear Regulator with Enable and Soft-Start Literature Number: SNVS492B LP38851 800 mA Fast-Response High-Accuracy Adjustable LDO Linear Regulator with Enable and Soft-Start General Description Features The LP38851-ADJ is a high current, fast response regulator which can maintain output voltage regulation with extremely low input to output voltage drop. Fabricated on a CMOS process, the device operates from two input voltages: VBIAS provides voltage to drive the gate of the N-MOS power transistor, while VIN is the input voltage which supplies power to the load. The use of an external bias rail allows the part to operate from ultra low VIN voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any output load current. The use of an N-MOS power transistor results in wide bandwidth, yet minimum external capacitance is required to maintain loop stability. The fast transient response of this device makes it suitable for use in powering DSP, Microcontroller Core voltages and Switch Mode Power Supply post regulators. The part is available in PSOP 8-pin, TO-220 7-pin, and TO-263 7-pin packages. Dropout Voltage: 115 mV (typical) at 800 mA load current. Low Ground Pin Current: 10 mA (typical) at 800 mA load current. Soft-Start: Programmable Soft-Start time. Precision ADJ Voltage: 1.5% for TJ = 25C, and 2.0% for 0C TJ +125C, across all line and load conditions Adjustable VOUT range of 0.80V to 1.8V Wide VBIAS Supply operating range of 3.0V to 5.5V Stable with 10F Ceramic capacitors Dropout voltage of 115 mV (typical) at 800 mA load current Precision VADJ across all line and load conditions: -- 1.5% VADJ for TJ = 25C -- 2.0% VADJ for 0C TJ +125C -- 3.0% VADJ for -40C TJ +125C Over-Temperature and Over-Current protection Available in 8 lead PSOP, 7 lead TO-220 and 7 lead TO-263 packages -40C to +125C Operating Junction Temperature Range Applications ASIC Power Supplies in: - Desktops, Notebooks, and Graphics Cards, Servers - Gaming Set Top Boxes, Printers and Copiers Server Core and I/O Supplies DSP and FPGA Power Supplies SMPS Post-Regulator Typical Application Circuit 30002501 (c) 2011 National Semiconductor Corporation 300025 www.national.com LP38851 800 mA Fast-Response High-Accuracy LDO Linear Regulator with Enable and Soft-Start September 13, 2011 LP38851 Ordering Information VOUT ADJ Order Number Package Type Package Drawing Supplied As LP38851S-ADJ TO263-7 TS7B Rail of 45 LP38851SX-ADJ TO263-7 TS7B Tape and Reel of 500 LP38851T-ADJ TO220-7 TA07B Rail of 45 LP38851MR-ADJ PSOP-8 MRA08A Rail of 95 LP38851MRX-ADJ PSOP-8 MRA08A Tape and Reel of 2500 Connection Diagrams 30002502 30002503 TO263-7, Top View TO220-7, Top View 30002504 PSOP-8, Top View Pin Descriptions TO220-7 Pin # TO263-7 Pin # PSOP-8 Pin # Pin Symbol 1 1 5 SS Soft-Start capacitor connection. Used to control the rise time of VOUT at turn-on. 2 2 6 EN Device Enable, High = On, Low = Off. 3 3 7 IN The unregulated voltage input 4 4 4 GND Ground 5 5 1 ADJ The feedback connection to set the output voltage 6 6 2 OUT The regulated output voltage 7 7 3 BIAS The supply for the internal control and reference circuitry. - - 8 N/C No internal connection Pin Description TAB TAB - TAB The TO220 and TO263 TAB is a thermal and electrical connection that is physically attached to the backside of the die, and used as a thermal heat-sink connection. See the Application Information section for details. - - DAP DAP The PSOP DAP is a thermal connection only that is physically attached to the backside of the die, and used as a thermal heatsink connection. See the Application Information section for details. www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Lead Temperature Soldering, 5 seconds ESD Rating Human Body Model (Note 2) Power Dissipation (Note 3) VIN Supply Voltage (Survival) VBIAS Supply Voltage (Survival) VSS SoftStart Voltage (Survival) -0.3V to +6.0V Internally Limited -40C to +150C Operating Ratings -65C to +150C (Note 1) VIN Supply Voltage VBIAS Supply Voltage 0.8V VOUT 1.2V 1.2V < VOUT 1.8V VEN Voltage IOUT Junction Temperature Range (Note 3) 260C 2 kV Internally Limited -0.3V to +6.0V -0.3V to +6.0V -0.3V to +6.0V (VOUT + VDO) to VBIAS 3.0V to 5.5V 4.5V to 5.5V 0.0V to VBIAS 0 mA to 800 mA -40C to +125C Electrical Characteristics Unless otherwise specified: VOUT = 0.80V, VIN = VOUT(NOM) + 1V, VBIAS = 3.0V, VEN = VBIAS, IOUT = 10 mA, CIN = COUT = 10 F, CBIAS = 1 F, CSS = open. Limits in standard type are for TJ = 25C only; limits in boldface type apply over the junction temperature (TJ) range of -40C to +125C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Symbol Parameter Conditions VOUT(NOM)+1V VIN VBIAS 4.5V, See (Note 7) 3.0V VBIAS 5.5V, Min Typ Max 492.5 485.0 500. 507.5 515.0 Units 10 mA IOUT 800 mA VADJ VADJ Accuracy VOUT(NOM)+1V VIN VBIAS 4.5V, See (Note 7) 3.0V VBIAS 5.5V, mV 490.0 500. 510.0 10 mA IOUT 800 mA, 0C TJ +125C VOUT VOUT Range 3.0V VBIAS 5.5V 0.80 1.20 4.5V VBIAS 5.5V 0.80 1.80 V Line Regulation, VIN (Note 4) VOUT(NOM)+1V VIN VBIAS - 0.04 - %/V VOUT/VBIAS Line Regulation, VBIAS (Note 4) 3.0V VBIAS 5.5V - 0.10 - %/V VOUT/IOUT Output Voltage Load Regulation (Note 5) 10 mA IOUT 800 mA - 0.2 - %/A Dropout Voltage (Note 6) IOUT = 800 mA - 115 150 200 mV VOUT = 0.80V VBIAS = 3.0V - 7.0 8.5 9.0 mA 1 100 300 A 3.0 3.8 4.5 mA 100 170 200 A 2.20 2.00 2.45 2.70 2.90 V 60 50 150 300 350 mV - 2.3 - A VOUT/VIN VDO IGND(IN) Quiescent Current Drawn from VIN Supply 10 mA IOUT 800 mA VEN 0.5V IGND(BIAS) Quiescent Current Drawn from VBIAS Supply 10 mA IOUT 800 mA VEN 0.5V UVLO Under-Voltage Lock-Out Threshold VBIAS rising until device is functional UVLO(HYS) Under-Voltage Lock-Out Hysteresis VBIAS falling from UVLO threshold until device is non-functional Output Short-Circuit Current VIN = VOUT(NOM) + 1V, VBIAS = 3.0V, VOUT = 0.0V ISC - 3 www.national.com LP38851 VOUT Voltage (Survival) IOUT Current (Survival) Junction Temperature Absolute Maximum Ratings (Note 1) LP38851 Symbol Parameter Conditions Min Typ Max Units 11.0 14.0 17.0 k CSS = 10 nF - 700 - s VEN = VBIAS - 0.01 - VEN = 0.0V, VBIAS = 5.5V -24 -21 -35 -43 -50 1.00 0.90 1.25 1.50 1.55 V 50 30 100 150 200 mV Soft-Start rSS Soft-Start internal resistance tSS Soft-Start time tSS = CSS x rSS x 5 Enable IEN ENABLE pin Current VEN(ON) Enable Voltage Threshold VEN rising until Output = ON VEN(HYS) Enable Voltage Hysteresis VEN falling from VEN(ON) until Output = OFF tOFF Turn-OFF Delay Time RLOAD x COUT << tOFF - 20 - tON Turn-ON Delay Time RLOAD x COUT << tON - 15 - VIN = VOUT(NOM) + 1V, f = 120 Hz - 72 - VIN = VOUT(NOM) + 1V, f = 1 kHz - 61 - VBIAS = VOUT(NOM) + 3V, f = 120 Hz - 54 - VBIAS = VOUT(NOM) + 3V, f = 1 kHz - 53 - f = 120 Hz - 1 - BW = 10 Hz - 100 kHz - 150 - BW = 300 Hz - 300 kHz - 90 - Thermal Shutdown Junction Temperature - 160 - Thermal Shutdown Hysteresis - 10 - TO220-7 - 60 - TO263-7 - 60 - PSOP-8 - 168 - TO220-7 - 3 - TO263-7 - 3 - PSOP-8 - 11 - A s AC Parameters PSRR (VIN) PSRR (VBIAS) Ripple Rejection for VIN Input Voltage Ripple Rejection for VBIAS Voltage Output Noise Density en Output Noise Voltage dB V/Hz VRMS Thermal Parameters TSD TSD(HYS) J-A J-C Thermal Resistance, Junction to Ambient(Note 3) Thermal Resistance, Junction to Case(Note 3, Note 8) C C/W Note 1: Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and conditions, see the Electrical Characteristics. Note 2: The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. Test method is per JESD22-A114. Note 3: Device power dissipation must be de-rated based on device power dissipation (PD), ambient temperature (TA), and package junction to ambient thermal resistance (JA). Additional heat-sinking may be required to ensure that the device junction temperature (TJ) does not exceed the maximum operating rating. See the Application Information section for details. Note 4: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage. Note 5: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from no load to full load. Note 6: Dropout voltage is defined as the input to output voltage differential (VIN - VOUT) where the input voltage is low enough to cause the output voltage to drop 2% from the nominal value. Note 7: VIN cannot exceed either VBIAS or 4.5V, whichever value is lower. Note 8: For TO-220 and TO-263: J-C refers to the BOTTOM surface of the package, under the epoxy body, as the 'CASE'. For PSOP-8: J-C refers to the DAP (aka: Exposed Pad) on BOTTOM surface of the package as the 'CASE'. www.national.com 4 Refer to the Typical Application Circuit. Unless otherwise specified: TJ = 25C, R1 = 1.40 k, R2 = 1.00 k, CFF= 180 pF, VIN = VOUT(NOM) + 1V, VBIAS = 3.0V, IOUT = 10 mA, CIN = 10 F Ceramic, COUT = 10 F Ceramic, CBIAS = 1 F Ceramic, , CSS = Open. VBIAS Ground Pin Current (IGND(BIAS)) vs VBIAS VBIAS Ground Pin Current (IGND(BIAS)) vs Temperature 30002587 30002561 VIN Ground Pin Current vs Temperature Load Regulation vs Temperature 30002563 30002562 Dropout Voltage (VDO) vs Temperature Output Current Limit (ISC) vs Temperature 30002565 30002566 5 www.national.com LP38851 Typical Performance Characteristics LP38851 VOUT vs Temperature VOUT vs VIN 30002567 30002572 UVLO Thresholds vs Temperature Soft-Start rSS Variation vs Temperature 30002568 30002575 VOUT vs CSS, 10 nF to 47 nF Enable Thresholds (VEN) vs Temperature 30002576 www.national.com 30002588 6 Enable Pull-Up Resistor (rEN) vs Temperature 30002589 30002590 VIN Line Transient Response VIN Line Transient Response 30002577 30002578 VBIAS Line Transient Response VBIAS Line Transient Response 30002579 30002580 7 www.national.com LP38851 Enable Pull-Down Current (IEN) vs Temperature LP38851 Load Transient Response, COUT = 10 F Ceramic Load Transient Response, COUT = 10 F Ceramic 30002582 30002581 Load Transient Response, COUT = 47 F Ceramic Load Transient Response, COUT = 47 F Ceramic 30002584 30002583 Load Transient Response, COUT = 68 F Tantalum Load Transient Response, COUT = 68 F Tantalum 30002585 www.national.com 30002586 8 LP38851 VBIAS PSRR VIN PSRR 30002570 30002571 Output Noise 30002569 9 www.national.com LP38851 Block Diagram 30002505 www.national.com 10 EXTERNAL CAPACITORS To assure regulator stability, input and output capacitors are required as shown in the Typical Application Circuit. FP = 1 / (2 x x CFF x (R1 || R2) ) Output Capacitor A minimum output capacitance of 10 F, ceramic, is required for stability. The amount of output capacitance can be increased without limit. The output capacitor must be located less than 1 cm from the output pin of the IC and returned to the device ground pin with a clean analog ground. Only high quality ceramic types such as X5R or X7R should be used, as the Z5U and Y5F types do not provide sufficient capacitance over temperature. Tantalum capacitors will also provide stable operation across the entire operating temperature range. However, the effects of ESR may provide variations in the output voltage during fast load transients. Using the minimum recommended 10 F ceramic capacitor at the output will allow unlimited capacitance, Tantalum and/or Aluminum, to be added in parallel. (4) It's important to note that at higher output voltages, where R1 is much larger than R2, the pole and zero are far apart in frequency. At lower output voltages the frequency of the pole and the zero mover closer together. The phase lead provided from CFF diminishes quickly as the output voltage is reduced, and has no effect when VOUT = VADJ. For this reason, relying on this compensation technique alone is adequate only for higher output voltages. For the LP38851, the practical minimum VOUT is 0.8V when a ceramic capacitor is used for COUT. Input Capacitor The input capacitor must be at least 10 F, but can be increased without limit. It's purpose is to provide a low source impedance for the regulator input. A ceramic capacitor, X5R or X7R, is recommended. Tantalum capacitors may also be used at the input pin. There is no specific ESR limitation on the input capacitor (the lower, the better). Aluminum electrolytic capacitors can be used, but are not recommended as their ESR increases very quickly at cold temperatures. They are not recommended for any application where the ambient temperature falls below 0C. Bias Capacitor The capacitor on the bias pin must be at least 1 F, and can be any good quality capacitor (ceramic is recommended). 30002521 FIGURE 1. FZERO and FPOLE vs Gain Feed Forward Capacitor, CFF (Refer to the Typical Application Circuit) When using a ceramic capacitor for COUT, the typical ESR value will be too small to provide any meaningful positive phase compensation, FZ, to offset the internal negative phase shifts in the gain loop. FZ = 1 / (2 x x COUT x ESR) SETTING THE OUTPUT VOLTAGE (Refer to the Typical Application Circuit) The output voltage is set using the external resistive divider R1 and R2. The output voltage is given by the formula: (5) (1) The resistors used for R1 and R2 should be high quality, tight tolerance, and with matching temperature coefficients. It is important to remember that, although the value of VADJ is guaranteed, the use of low quality resistors for R1 and R2 can easily produce a VOUT value that is unacceptable. It is recommended that the values selected for R1 and R2 are such that the parallel value is less than 10 k. This is to prevent internal parasitic capacitances on the ADJ pin from interfering with the FZ pole set by R1 and CFF. A capacitor placed across the gain resistor R1 will provide additional phase margin to improve load transient response of the device. This capacitor, CFF, in parallel with R1, will form a zero in the loop response given by the formula: FZ = 1 / (2 x x CFF x R1) (2) For optimum load transient response select CFF so the zero frequency, FZ, falls between 500 kHz and 750 kHz. CFF = 1 / (2 x x R1 x FZ) ( (R1 x R2) / (R1 + R2) ) 10 k (6) Table 1 lists some suggested, best fit, standard 1% resistor values for R1 and R2, and a standard 10% capacitor values for CFF, for a range of VOUT values. Other values of R1, R2, and CFF are available that will give similar results. (3) 11 www.national.com LP38851 The phase lead provided by CFF diminishes as the DC gain approaches unity, or VOUT approaches VADJ. This is because CFF also forms a pole with a frequency of: Application Information LP38851 diode clamped to ground. A Schottky diode is recommended for this diode clamp. TABLE 1. VOUT R1 0.8V 1.07 k R2 CFF FZ 1.78 k 220 pF 676 kHz 0.9V 1.50 k 1.87 k 180 pF 589 kHz 1.00V 1.00 k 1.00 k 270 pF 589 kHz 1.1V 1.65 k 1.37 k 150 pF 643 kHz 1.2V 1.40 k 1.00 k 180 pF 631 kHz 1.3V 1.15 k 715 220 pF 629 kHz 1.4V 1.07 k 590 220 pF 676 kHz 1.5V 2.00 k 1.00 k 120pF 663 kHz 1.6V 1.65 k 750 150 pF 643 kHz 1.7V 2.55 k 1.07 k 100 pF 624 kHz 1.8V 2.94 k 1.13 k 82 pF 660 kHz REVERSE VOLTAGE A reverse voltage condition will exist when the voltage at the output pin is higher than the voltage at the input pin. Typically this will happen when VIN is abruptly taken low and COUT continues to hold a sufficient charge such that the input to output voltage becomes reversed. The NMOS pass element, by design, contains no body diode. This means that, as long as the gate of the pass element is not driven, there will not be any reverse current flow through the pass element during a reverse voltage event. The gate of the pass element is not driven when VBIAS is below the UVLO threshold, or when the Enable pin is held low. When VBIAS is above the UVLO threshold, and the Enable pin is above the VEN(ON) threshold, the control circuitry is active and will attempt to regulate the output voltage. Since the input voltage is less than the output voltage the control circuit will drive the gate of the pass element to the full VBIAS potential when the output voltage begins to fall. In this condition, reverse current will flow from the output pin to the input pin , limited only by the RDS(ON) of the pass element and the output to input voltage differential. Discharging an output capacitor up 1000 F in this manner will not damage the device as the current will rapidly decay. However, continuous reverse current should be avoided. Please refer to Application Note AN-1378 for additional information on how resistor tolerances affect the calculated VOUT value. INPUT VOLTAGE The input voltage (VIN) is the high current external voltage rail that will be regulated down to a lower voltage, which is applied to the load. The input voltage must be at least VOUT + VDO, and no higher than whatever value is used for VBIAS. For applications where VBIAS is higher than 4.5V, VIN must be no greater than 4.5V, otherwise output voltage accuracy may be affected. SOFT-START The LP38851 incorporates a Soft-Start function that reduces the start-up current surge into the output capacitor (COUT) by allowing VOUT to rise slowly to the final value. This is accomplished by controlling VREF at the SS pin. The soft-start timing capacitor (CSS) is internally held to ground until both VBIAS rises above the Under-Voltage Lock-Out threshold (ULVO) and the Enable pin is higher than the VEN(ON) threshold. VREF will rise at an RC rate defined by the internal resistance of the SS pin (rSS), and the external capacitor connected to the SS pin. This allows the output voltage to rise in a controlled manner until steady-state regulation is achieved. Typically, five time constants are recommended to assure that the output voltage is sufficiently close to the final steady-state value. During the soft-start time the output current can rise to the built-in current limit. BIAS VOLTAGE The bias voltage (V BIAS) is a low current external voltage rail required to bias the control circuitry and provide gate drive for the N-FET pass transistor. When VOUT is set to 1.20V, or less, VBIAS may be anywhere in the operating range of 3.0V to 5.5V. If VOUT is set higher than 1.20V , VBIAS must be between 4.5V and 5.5V to ensure proper operation of the device. UNDER VOLTAGE LOCKOUT The bias voltage is monitored by a circuit which prevents the device from functioning when the bias voltage is below the Under-Voltage Lock-Out (UVLO) threshold of approximately 2.45V. As the bias voltage rises above the UVLO threshold the device control circuitry becomes active. There is approximately 150 mV of hysteresis built into the UVLO threshold to provide noise immunity. When the bias voltage is between the UVLO threshold and the Minimum Operating Rating value of 3.0V the device will be functional, but the operating parameters will not be within the guaranteed limits. Soft-Start Time = CSS x rSS x 5 Since the VOUT rise will be exponential, not linear, the in-rush current will peak during the first time constant (), and VOUT will require four additional time constants (4) to reach the final value (5) . After achieving normal operation, should either VBIAS fall below the ULVO threshold, or the Enable pin fall below the VEN (OFF) threshold, the device output will be disabled and the SoftStart capacitor (CSS) discharge circuit will become active. The CSS discharge circuit will remain active until VBIAS falls to 500 mV (typical). When VBIAS falls below 500 mV (typical), the CSS discharge circuit will cease to function due to a lack of sufficient biasing to the control circuitry. Since VREF appears on the SS pin, any leakage through CSS will cause VREF to fall, and thus affect VOUT. A leakage of 50 nA (about 10 M) through CSS will cause VOUT to be approximately 0.1% lower than nominal, while a leakage of 500 nA (about 1 M) will cause VOUT to be approximately 1% lower than nominal. Typical ceramic capacitors will have a factor of SUPPLY SEQUENCING There is no requirement for the order that VIN or VBIAS are applied or removed. One practical limitation is that the Soft-Start circuit starts charging CSS when both VBIAS rises above the UVLO threshold and the Enable pin is above the VEN(ON) threshold. If the application of VIN is delayed beyond this point the benefits of Soft-Start will be compromised. In any case, the output voltage cannot be guaranteed until both VIN and VBIAS are within the range of guaranteed operating values. If used in a dual-supply system where the regulator output load is returned to a negative supply, the output pin must be www.national.com (7) 12 The total power dissipation of the device is the sum of three different points of dissipation in the device. The first part is the power that is dissipated in the NMOS pass element, and can be determined with the formula: PD(PASS) = (VIN - VOUT) x IOUT (8) The second part is the power that is dissipated in the bias and control circuitry, and can be determined with the formula: PD(BIAS) = VBIAS x IGND(BIAS) (9) where IGND(BIAS) is the portion of the operating ground current of the device that is related to VBIAS. The third part is the power that is dissipated in portions of the output stage circuitry, and can be determined with the formula: PD(IN) = VIN x IGND(IN) (10) where IGND(IN) is the portion of the operating ground current of the device that is related to VIN. The total power dissipation is then: PD = PD(PASS) + PD(BIAS) + PD(IN) 30002523 (11) The maximum allowable junction temperature rise (TJ) depends on the maximum anticipated ambient temperature (TA) for the application, and the maximum allowable operating junction temperature (TJ(MAX)) . FIGURE 2. Typical CSS vs COUT Values The CSS capacitor must be connected to a clean ground path back to the device ground pin. No components, other than CSS, should be connected to the SS pin, as there could be adverse effects to VOUT. If the Soft-Start function is not needed the SS pin should be left open, although some minimal capacitance value is always recommended. (12) The maximum allowable value for junction to ambient Thermal Resistance, JA, can be calculated using the formula: (13) ENABLE OPERATION The Enable pin (EN) provides a mechanism to enable, or disable, the regulator output stage. The Enable pin has an internal pull-up, through a typical 160 k resistor, to VBIAS. If the Enable pin is actively driven, pulling the Enable pin above the VEN threshold of 1.25V (typical) will turn the regulator output on, while pulling the Enable pin below the VEN threshold will turn the regulator output off. There is approximately 100 mV of hysteresis built into the Enable threshold provide noise immunity. If the Enable function is not needed this pin should be left open, or connected directly to VBIAS. If the Enable pin is left open, stray capacitance on this pin must be minimized, otherwise the output turn-on will be delayed while the stray capacitance is charged through the internal resistance (rEN). Heat-Sinking The TO-220 Package The TO220-5 package has a JA rating of 60C/W and a JC rating of 3C/W. These ratings are for the package only, no additional heat-sinking, and with no airflow. If the needed JA, as calculated above, is greater than or equal to 60C/W then no additional heat-sinking is required since the package can safely dissipate the heat and not exceed the operating TJ(MAX). If the needed JA is less than 60C/W then additional heat-sinking is needed. The thermal resistance of a TO-220 package can be reduced by attaching it to a heat sink or a copper plane on a PC board. If a copper plane is to be used, the values of JA will be same as shown in next section for TO-263 package. The heat-sink to be used in the application should have a heat-sink to ambient thermal resistance, HA: POWER DISSIPATION AND HEAT-SINKING Additional copper area for heat-sinking may be required depending on the maximum device dissipation (PD) and the maximum anticipated ambient temperature (TA) for the device. Under all possible conditions, the junction temperature must be within the range specified under operating conditions. (14) where JA is the required total thermal resistance from the junction to the ambient air, CH is the thermal resistance from the case to the surface of the heart-sink, and JC is the thermal resistance from the junction to the surface of the case. 13 www.national.com LP38851 10X difference in leakage between 25C and 85C, so the maximum ambient temperature must be included in the capacitor selection process. Typical CSS values will be in the range of 1 nF to 100 nF, providing typical Soft-Start times in the range of 70 s to 7 ms (5). Values less than 1 nF can be used, but the Soft-Start effect will be minimal. Values larger than 100 nF will provide soft-start, but may not be fully discharged if VBIAS falls from the UVLVO threshold to less than 500 mV in less than 100 s. Figure 2 shows the relationship between the COUT value and a typical CSS value. LP38851 ing JA is 35C/W and the maximum junction temperature is 125C. For this equation, JC is about 3C/W for a TO-220 package. The value for CH depends on method of attachment, insulator, etc. CH varies between 1.5C/W to 2.5C/W. Consult the heat-sink manufacturer datasheet for details and recommendations. Heat-Sinking The PSOP-8 Package The LP38851MR package has a JA rating of 168C/W, and a JC rating of 11C/W. The JA rating of 168C/W includes the device DAP soldered to an area of 0.008 square inches (0.09 in x 0.09 in) of 1 ounce copper, with no airflow. Heat-Sinking The TO-263 Package The TO-263 package has a JA rating of 60C/W, and a JC rating of 3C/W. These ratings are for the package only, no additional heat-sinking, and with no airflow. The TO-263 package uses the copper plane on the PCB as a heat-sink. The tab of this package is soldered to the copper plane for heat sinking. Figure 3 shows a curve for the JA of TO-263 package for different copper area sizes, using a typical PCB with 1 ounce copper and no solder mask over the copper area for heat-sinking. 30002527 FIGURE 5. JA vs Copper (1 Ounce) Area for the PSOP-8 Package Increasing the copper area soldered to the DAP to 1 square inch of 1 ounce copper, using a dog-bone type layout, will improve the JA rating to 98C/W. Figure 5 shows that increasing the copper area beyond 1 square inch produces very little improvement. 30002525 FIGURE 3. JA vs Copper (1 Ounce) Area for the TO-263 package Figure 3 shows that increasing the copper area beyond 1 square inch produces very little improvement. The minimum value for JA for the TO-263 package mounted to a PCB is 32C/W. 30002528 FIGURE 6. Maximum Power Dissipation vs Ambient Temperature for the PSOP-8 Package Figure 6 shows the maximum allowable power dissipation for the PSOP-8 package for a range of ambient temperatures, assuming JA is 98C/W and the maximum junction temperature is 125C. 30002526 FIGURE 4. Maximum Power Dissipation vs Ambient Temperature for the TO-263 Package Figure 4 shows the maximum allowable power dissipation for TO-263 packages for different ambient temperatures, assumwww.national.com 14 LP38851 Physical Dimensions inches (millimeters) unless otherwise noted TO-220 7-Lead, Stagger Bend Package (TO220-7) NS Package Number TA07B TO-263 7-Lead, Molded, Surface Mount Package (TO263-7) NS Package Number TS7B 15 www.national.com LP38851 PSOP, 8 Lead, Molded, 0.050 in Pitch NS Package Number MRA08A www.national.com 16 LP38851 Notes 17 www.national.com LP38851 800 mA Fast-Response High-Accuracy LDO Linear Regulator with Enable and Soft-Start Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated